Vectronics VEC-4001K Manuel d'utilisateur

VEC-4001K Owner’s Manual Professional Function Generator 1 INTRODUCTION This easy-to-build professional grade function generator kit provides precisi

VEC-4001K Owner’s Manual Professional Function Generator 10 STEP-BY-STEP CONSTRUCTION In these instructions, when you see the term install, this mean

VEC-4001K Owner’s Manual Professional Function Generator 11 ! ! 9.#Install a 1.6K at R31 and solder. ! ! 10.#Install a 1.6K at R32 and solder.

VEC-4001K Owner’s Manual Professional Function Generator 12 Locate two (2) 1N4007 diodes. ! ! 26.#Install a 1N4007 at D1 and solder. ! ! 27.#Inst

VEC-4001K Owner’s Manual Professional Function Generator 13 ! ! 47.#Find the .082 µF polyester ceramic capacitor (green, marked .082). Install at

VEC-4001K Owner’s Manual Professional Function Generator 14 ! ! 57. Install a 2200 µF at C1 and solder. ! ! 58. Install a 2200 µF at C2 and sol

VEC-4001K Owner’s Manual Professional Function Generator 15 ! ! 65. Find a eight-pin IC socket. Orient to U2, install, and solder all 8 pins. ! !

VEC-4001K Owner’s Manual Professional Function Generator 16 ! ! 76. Cut to 1 3/4" and prepare jumper. Install at JMP3 and solder. ! ! 77.

VEC-4001K Owner’s Manual Professional Function Generator 17 Locate three (3) 10K pots (marked B103 or B10K). Using a flat washer and a nut, install

VEC-4001K Owner’s Manual Professional Function Generator 18 SW3SW1J1J3 J2R2R3R1RedYellowBlackColor CodeTop or "clockwise"Middle or "c

VEC-4001K Owner’s Manual Professional Function Generator 19 ! ! 107. Cut and prep another set of 6" wires (red, yellow, and black). Find R3. !

VEC-4001K Owner’s Manual Professional Function Generator 2 BEFORE YOU START BUILDING Experience shows there are four common mistakes builders make.

VEC-4001K Owner’s Manual Professional Function Generator 20 Locate the three-wire harness connected to Amplitude control R2. ! ! 128. Connect R2 red

VEC-4001K Owner’s Manual Professional Function Generator 21 3. Finally, check electrolytic capacitors and diodes for correct polarity. Does the plu

VEC-4001K Owner’s Manual Professional Function Generator 22 R4 R5 R6R7R8R9R10100101102103104105Low SetBottom View To check the generator's outpu

VEC-4001K Owner’s Manual Professional Function Generator 23 * Note that counters designed for RF work may not read 10 Hz or even 100 Hz with accurac

VEC-4001K Owner’s Manual Professional Function Generator 24 100 1-10 Hz101 10-100 Hz102 100-1000 Hz103 1 kHz - 10 kHz104 10 kHz - 100 kHz105 10

VEC-4001K Owner’s Manual Professional Function Generator 25 OPERATING INSTRUCTIONS Control Functions: See the follwing diagram for control locations

VEC-4001K Owner’s Manual Professional Function Generator 26 IN CASE OF DIFFICULTY If your VEC-4001K Generator fails to perform to your expectation, p

VEC-4001K Owner’s Manual Professional Function Generator 27 THEORY OF OPERATION AND SPECIFICATIONS Your generator kit is built around the MAX038CPP,

VEC-4001K Owner’s Manual Professional Function Generator 3 behind the lead as you extract it--especially if you are working on a double-sided board w

VEC-4001K Owner’s Manual Professional Function Generator 4 Multilayer271(270 pF)Ceramic Discs||1uF35V+-104Electrolytic 1 uF10 pF = 100100 pF =

VEC-4001K Owner’s Manual Professional Function Generator 5 EmitterFlat SideMetal TabMetal Can Device Plastic Device Tab-cooled Device Integrated Circ

VEC-4001K Owner’s Manual Professional Function Generator 6 PARTS LIST Your kit should contain all of the parts listed below. Please identify and inv

VEC-4001K Owner’s Manual Professional Function Generator 7 ! 1 680 pF disc ceramic capacitor (681) C20 200-0680-1 ! 2 .001 µF disc ceramic capacito

VEC-4001K Owner’s Manual Professional Function Generator 8 ! 1 LM358 dual op-amp U3 324-0358 ! 1 MAX038CPP function generator IC U1 325-0038 ! 1